| Част Не | Производител | Заявление |
|---|
| MAX6318LHUK38DX-T | MaximIC | Microprocessor supervisory circuit with watchdog and manual reset,(watchdog input,reset output active-low,push/pull; active-high,push/pull).Factory-trimmed reset threshold(typ) 3.800V min, reset timeout 1.12sec,typ watchdog timeout 102ms |
| OP07D/D | MaximIC | Low offset voltage operational amplifier. |
| MAX6327UR31-T | MaximIC | Ultra-low-power microprocessor supervisory circuit (reset output active-high, push-pull). Reset threshold (typ) 3.080V. Standard version. Order increment 2.5k |
| MAX417MJA | MaximIC | 1.2microA max, dual, single-supply op amp. |
| MAX7409CUA | MaximIC | 5th-order, lowpass, switched-capacitor filter. Filter response bessel, operating voltage +5V |
| MAX327CSE | MaximIC | Quad, SPTS, ultra-low leakage, CMOS analog switch. |
| MAX336CPI | MaximIC | 16-channel, low-leakage, CMOS analog multiplexer. |
| DG201C/D | MaximIC | Quad SPST CMOS analog switch. |
| ADC0820BJ | MaximIC | CMOS high speed 8-bit A/D converter with track/hold function. INL(LSB) +-1/2. |
| MAX984CSE | MaximIC | Ultra-low-power, open-drain, quad comparator. Internal precision reference 2%. Internal hysteresis no. |
| MAX520BCAP | MaximIC | Quad, 2-wire serial 8-bit DAC with Rail-to-Rail, unbuffered outputs. TUE(LSB) 2. |
| MAX329C/D | MaximIC | Ultra-low lealage monolithic CMOS analog multiplexer. |
| MAX6321HPUK41AY-T | MaximIC | Microprocessor supervisory circuit with watchdog (watchdog input, reset outputs active-high, push/pull and active-low, open-drain).Factory-trimmed reset threshold(typ) 4.100V, reset timeout(min) 1ms, watchdog timeout(typ) 1.6sec |
| MAX6316LUK26DW-T | MaximIC | Microprocessor supervisory circuit with watchdog and manual reset (watchdog input,manual reset input,reset output active-low,push/pull).Factory-trimmed reset threshold (typ) 2.630V, min reset timeout 1120ms, typ watchdog timeout 6.3ms |
| MAX6317HUK44BZ-T | MaximIC | Microprocessor supervisory circuit with watchdog and manual reset (watchdog input,manual reset input,reset output active-high, push/pull).Factory-trimmed reset threshold (typ) 4.390V, min reset timeout 20ms, typ watchdog timeout 25.6sec |
| MAX1638EEG | MaximIC | High-speed step-down controller with synchronous rectification for CPU power |
| MAX9052BESA | MaximIC | Micropower, single-supply, dual comparator + precision reference IC. |
| MAX6321HPUK43AX-T | MaximIC | Microprocessor supervisory circuit with watchdog (watchdog input, reset outputs active-high, push/pull and active-low, open-drain).Factory-trimmed reset threshold(typ) 4.300V, reset timeout(min) 1ms, watchdog timeout(typ) 102ms |
| MAX1651CPA | MaximIC | 3.3V or adjustable, high-efficiency, low-dropout, step-down DC-DC controller |
| MAX488ESA | MaximIC | Low-power, slew-rate-limited RS-485/RS-422 transceiver. Full-duplex. Data rate 0.25Mbps. Slew-rate limited - yes. Low-power shutdown - no. Receiver/driver enable - no. Quiescent current - 120 microA. Number of transmitter on bus - 32. |
| MAX907EPA | MaximIC | Single high-speed, ultra low-power, single 4.4V to 5.5V supply operation TTL comparator. |
| MAX521ACPP | MaximIC | Octal, 2-wire serial 8-bit DAC with Rail-to-Rail, unbuffered outputs. TUE(LSB) 1. |
| MAX2268EUE | MaximIC | 2.7V, single-supply, cellular-band linear power amplifier. Low average CDMA current consumption in typical urban scenario 90mA. TSSOP-EP 5mm x 6.4mm. |
| MAX485EESA | MaximIC | +-15kV ESD-protected, low-power, RS-485/RS-422 transceiver. Half-duplex. Data rate 2.5Mbps. Slew-rate limited - no. Low-power shutdown - no. Receiver/driver enable - yes. Quiescent current - 300 microA. Number of transmitter on bus - 32. |
| MAX812TEUS-T | MaximIC | Microprocessor voltage monitor with manual reset input. Reset threshold voltage 3.08V. Push-pull active-high reset output. |
| MAX6317HUK46AW-T | MaximIC | Microprocessor supervisory circuit with watchdog and manual reset (watchdog input,manual reset input,reset output active-high, push/pull).Factory-trimmed reset threshold (typ) 4.630V, min reset timeout 1ms, typ watchdog timeout 6.3ms |
| MAX4512EPE | MaximIC | Quad, Rail-to-Rail, fault-protected, SPST analog switch. |
| MAX642AEJA | MaximIC | +12V fixed output, 10W CMOS step-up switching regulator. 5% output accuracy |
| MAX809JEUR-T | MaximIC | Microprocessor reset circuit. Reset threshold 4.00V. Push-pull active-high reset. 2.5k increments. |
| MAX6317HUK38DZ-T | MaximIC | Microprocessor supervisory circuit with watchdog and manual reset (watchdog input,manual reset input,reset output active-high, push/pull).Factory-trimmed reset threshold (typ) 3.800V, min reset timeout 1.12sec, typ watchdog timeout 25.6sec |
