| Част Не | Производител | Заявление |
|---|
| MAX6321HPUK25DX-T | MaximIC | Microprocessor supervisory circuit with watchdog (watchdog input, reset outputs active-high, push/pull and active-low, open-drain).Factory-trimmed reset threshold(typ) 2.500V, reset timeout(min) 1.12sec, watchdog timeout(typ) 102ms |
| MAX6315US37D3-T | MaximIC | Open-drain microprocessor reset circuit. Reset threshold(nom) 3.70V. Reset timeout period(min) 140ms. |
| IH5040C/D | MaximIC | General-purpose CMOS analog switch. Single pole, single throw (SPST) |
| MAX260BCNG | MaximIC | Microprocessor programmable universal active filter. Accuracy 2%. |
| MAX152EAP | MaximIC | +3V, 8-bit ADC with 1 micro A power-down |
| MAX2651EUB | MaximIC | GSM900 and DSC1800 dual-band, low-noise amplifier. |
| MAX835EUK-T | MaximIC | Micropower, latching voltage monitor. Push/pull output. |
| MX7533SQ | MaximIC | CMOS low-cost 10 bit multiplying D/A converter. Error 0.2% |
| MAX6336US18D2-T | MaximIC | Ultra-low-voltage, low-power microprocessor circuit with manual reset (reset output active-low, push/pull . Reset threshold(typ) 1.8V, reset timeout(min) 20ms. |
| MAX6316LUK40CX-T | MaximIC | Microprocessor supervisory circuit with watchdog and manual reset (watchdog input,manual reset input,reset output active-low,push/pull).Factory-trimmed reset threshold (typ) 4.000V, min reset timeout 140ms, typ watchdog timeout 102ms |
| MAX1205EMH | MaximIC | +5V single-supply, 1Msps, 14-bit self-calibrating ADC |
| MAX6318MHUK35AZ-T | MaximIC | Microprocessor supervisory circuit with watchdog input (watchdog input,reset output active-high,push/pull and active-low, bidirectional).Factory-trimmed reset threshold(typ) 3.500V, reset timeout(min) 1ms, watchdog timeout(typ) 25.6sec |
| MAX8216ESD | MaximIC | +-5V, +-15V dedicated microprocessor voltage monitor. |
| MAX6314US30D3-T | MaximIC | 68H11/bidirectional-compatible microprocessor reset circuit. Reset threshold(nom) 3.00V. Reset timeout period(min) 140ms. |
| MAX6319LHUK46B-T | MaximIC | Microprocessor supervisory circuit with manual reset (manual reset input, reset outputs active-low,push/pull and active-high, push/pull).Factory-trimmed reset threshold(typ) 4.630V, reset timeout(min) 20ms |
| MAX4604CPE | MaximIC | Low on-resistance (5om max), quad, SPST, CMOS analog switches (four NC switches). |
| MAX516BCWG | MaximIC | Quad comparator with programmable threshold. Error (LSB) +-2 |
| MAX635ACPA | MaximIC | Preset -5V output or adjuistable output with 2 resistors, CMOS switching regulator. Output accuracy 5%. |
| MAX745C/D | MaximIC | Switch-mode lithium-lon battery-charger |
| MX580JESA | MaximIC | High precision +2.5V reference. Tolerance +-75mV |
| MAX305CSE | MaximIC | Precision, dual, high-speed analog switch. |
| MX7828KP | MaximIC | CMOS, high-speed, 8-bit ADC with multiplex. Error (LSB) +-1 |
| MAX4274BEEUA | MaximIC | Dual, Rail-to-Rail, GainAmp op amp with precision internal gain-setting resistors. Rf/Rg inverting gain 24, 1+ (Rf/Dg) noninverting gain 25, -3dB BW 590kHz. |
| MAX6320PUK37AY-T | MaximIC | Microprocessor supervisory circuit with watchdog and manual reset (watchdog input,manual reset input, reset output active-low, open-drain).Factory-trimmed reset threshold(typ) 3.700V, reset timeout(min) 1ms, watchdog timeout(typ) 1.6sec |
| MAX242CWN | MaximIC | +5V-powered, multichannel RS-232 driver-receiver. |
| MAX9004EUB | MaximIC | Low-power, high-speed, single-supply op amp + comparator + reference IC. Op-Amp gain stability 10V/V. Op-Amp gain bandwidth 8MHz. Shutdown mode. |
| MAX1679EUA | MaximIC | Single-cell Li+ battery charger for current-limited supply. |
| MAX3261CCJ | MaximIC | Single +5V, fully integrated, 1.25Gbps laser diode driver. |
| MX7224KCWN | MaximIC | CMOS 8-bit DAC with output amplifier. Error +2 LSB. |
| MAX6317HUK43CZ-T | MaximIC | Microprocessor supervisory circuit with watchdog and manual reset (watchdog input,manual reset input,reset output active-high, push/pull).Factory-trimmed reset threshold (typ) 4.300V, min reset timeout 140ms, typ watchdog timeout 25.6sec |
