| Част Не | Производител | Заявление |
|---|
| MAX6380UR35-T | MaximIC | Ultra-low-power voltage detector, 3.5V |
| MAX1093AEEG | MaximIC | 250ksps, +3V, 4-channel single-ended/2-channel pseudo-differential, 10-bit ADCs with +2.5V reference and parallel interface. INL (LSB) 0.5 |
| MAX4275BEEUA | MaximIC | Dual, Rail-to-Rail, GainAmp op amp with precision internal gain-setting resistors. Rf/Rg inverting gain 24, 1+ (Rf/Dg) noninverting gain 25, -3dB BW 590kHz. |
| MXT429CPA | MaximIC | High-speed, 6A single MOSFET driver. 4.5V t0 18V supply range. |
| MAX6334UR17D2-T | MaximIC | Ultra-low-voltage, low power microprocessor reset circuit. Reset threshold(typ) 1.7V, reset timeout(min) 20ms. |
| MAX991EUA | MaximIC | Dual, micropower, low-voltage, Rail-to-Rail I/O comparator. Push/pull output stage sinks and sources. |
| MAX996ESD | MaximIC | Quad, micropower, low-voltage, Rail-to-Rail I/O comparator. Open-drain output voltage extends beyond Vcc. |
| MAX5104CEE | MaximIC | Low-power, dual, voltage-output, 12-bit DAC with serial interface. INL (LSB) +-4 |
| MAX633BCSA | MaximIC | CMOS fixed +15V output voltage, adjustable output with 2 resistors step-up switching regulator. 10% output accuracy. |
| MAX809LEXR-T10 | MaximIC | Microprocessor reset circuit. Reset threshold 4.63V. Push-pull active-high reset. 10k increments. |
| MAX6316LUK32CX-T | MaximIC | Microprocessor supervisory circuit with watchdog and manual reset (watchdog input,manual reset input,reset output active-low,push/pull).Factory-trimmed reset threshold (typ) 3.200V, min reset timeout 140ms, typ watchdog timeout 102ms |
| MAX242CAP | MaximIC | +5V-powered, multichannel RS-232 driver-receiver. |
| MAX6317HUK48BX-T | MaximIC | Microprocessor supervisory circuit with watchdog and manual reset (watchdog input,manual reset input,reset output active-high, push/pull).Factory-trimmed reset threshold (typ) 4.800V, min reset timeout 20ms, typ watchdog timeout 102ms |
| MAX4274BJESA | MaximIC | Dual, Rail-to-Rail, GainAmp op amp with precision internal gain-setting resistors. Rf/Rg inverting gain 49, 1+ (Rf/Dg) noninverting gain 50, -3dB BW 310kHz. |
| MAX4547EPE | MaximIC | Single,low-voltage T-switch designed for switching RF and video signals from DC to 300MHz in 50om and 75om systems. |
| MAX6310UK50D2-T | MaximIC | Multiple-input, programmable reset IC(push/pull reset output,factory-set reset threshold on Vcc,1 additional undervoltage reset input,negative overvoltage reset input).Factory-trimmed reset thresholds 4.875(min),5.125(max). Nominal timeout period 20ms. |
| MAX858ESA | MaximIC | 5V or 3.3V output, step-up DC-DC converter. |
| MAX6316LUK48AX-T | MaximIC | Microprocessor supervisory circuit with watchdog and manual reset (watchdog input,manual reset input,reset output active-low,push/pull).Factory-trimmed reset threshold (typ) 4.800V, min reset timeout 1ms, typ watchdog timeout 102ms |
| MAX6321HPUK38AZ-T | MaximIC | Microprocessor supervisory circuit with watchdog (watchdog input, reset outputs active-high, push/pull and active-low, open-drain).Factory-trimmed reset threshold(typ) 3.800V, reset timeout(min) 1ms, watchdog timeout(typ) 25.6sec |
| MAX872CSA | MaximIC | 10microA, low-dropout, precision voltage reference. Output voltage 2.500V +-0.2%. Wide operating voltage range 2.7V to 20V. Line regulation over temp. 20microV/V. Load regulation over temp. 0.6mV/mA max |
| MAX666ESA | MaximIC | Dual Mode 5V or programmable micropower voltage positive with on-chip vow-battery detection circuitry regulator. |
| MAX6321HPUK36DZ-T | MaximIC | Microprocessor supervisory circuit with watchdog (watchdog input, reset outputs active-high, push/pull and active-low, open-drain).Factory-trimmed reset threshold(typ) 3.600V, reset timeout(min) 1.12sec, watchdog timeout(typ) 25.6sec |
| MAX643BC/D | MaximIC | +15V fixed output, 10W CMOS step-up switching regulator. 10% output accuracy |
| MAX6320PUK43CY-T | MaximIC | Microprocessor supervisory circuit with watchdog and manual reset (watchdog input,manual reset input, reset output active-low, open-drain).Factory-trimmed reset threshold(typ) 4.300V, reset timeout(min) 140ms, watchdog timeout(typ) 1.6sec |
| MAX4284ESD | MaximIC | Quad, open-loop, unity-gain stable amplifier |
| MAX6318MHUK39CW-T | MaximIC | Microprocessor supervisory circuit with watchdog input (watchdog input,reset output active-high,push/pull and active-low, bidirectional).Factory-trimmed reset threshold(typ) 3.900V, reset timeout(min) 140ms, watchdog timeout(typ) 6.3ms |
| MAX6321HPUK48BY-T | MaximIC | Microprocessor supervisory circuit with watchdog (watchdog input, reset outputs active-high, push/pull and active-low, open-drain).Factory-trimmed reset threshold(typ) 4.800V, reset timeout(min) 20ms, watchdog timeout(typ) 1.6sec |
| MAX882CPA | MaximIC | 3.3V or adjustable, low-dropout, low current, 200mA linear regulator. 7microA standby mode. |
| MAX6319MHUK27C-T | MaximIC | Microprocessor supervisory circuit with manual reset (manual reset input, reset outputs active-high, push/pull and active-low, bidirectional).Factory-trimmed reset threshold(typ) 2.700V, reset timeout(min) 140ms |
| MX574AKP | MaximIC | Industry standard complete 12-bit A/D converter. 25 microsec. max conversion time. Linearity (LSBs) 1/2. TEMPCO(ppm/C) 27. |
